Futaba 8SSHP Bedienungsanleitung

FutabaDIGITAL PROPORTIONALRADIO CONTROLPCMSINGLE STICKPULSE CODE MODULATION SYSTEMD60421

27. Tachometer/timerThetachometer/timerhas the following func-tions:1. Tachometer•Measurement by external sensor.•Two blade propeller specifications.

OPERATING INSTRUCTIONS1. TachometerSet the tachometer/times POWER switchto ON. appears on the display. Next, press theMODE SEL key switch at the up

MODE SEL KEY SW.2 UP TIMERSet the tachometer/timer POWER switch to ON.is displayed. Next, press the MODE.SELkey switch at the upper right-hand corn

29 Charging and DSC (Direct ServoController) connectorThis connector is used as both the internal Nicadbattery charging connector and the DSC con-nec

30 Power switchTransmitter lock-type power switch. To turn the switchon and off, pull the knob forward and set it to the de-sired position.31 AntennaS

37 Back coverTo operate the trimmers and switches on the trimmerpanel [38] , remove this cover as shown in Fig. 28.Remove the back cover by pulling

B PitchA Inverted flight low-side trimmerB Inverted flight high-side trimmerC Inverted flightFS switchFig. 33• The inverted flight functioncan be tur

Fig. 37Fig. 384. Normal pitch trimmerAdjusted to match normalflight.5. This trimmer sets the lowpitch (minus pitch) when thethrottle hold switch[2

Rudder servoSettable withinthis range bytrimmer [16] .Fig. 4117. This trimmer sets therudder servo throw anddirection when the rudderbutton [3

G. Cyclic Corrective Pitch Mixing (optional)CCP mixing is performed after the helicopter correc-tive pitch and cyclic pitch control systems are el

Thank you for purchasing a Futaba digitalproportional radio control set.Please read this manual carefully before usingyour set.When reading this manua

H. Servo reversing switchesThese switches reverse the direction of the servos.They are very convenient when connecting the linkage.Fig. 49CH8 switchc

Each servo moves to the neutral position exceptthe throttle servo which moves to the slow positionthat was just set.6 Pail safe for all channels c

J Channel select switch•This switch selects the channel to be set by ATV orFS, when used in conjunction with item [1] ATV/FSbutton previously

RECEIVER AND SERVOSFS (Fail safe) and HOLD functions•The HOLD function holds all the servosat the po-sition immediately before a bad set of signal isr

PCM RECEIVER FP-R118GP• System checking can be performed with this lamp.•When the receiver and servo side Nicd is connect-ed and this LED is on, radio

Five battery pack 6V connector Motor regulatedpower supply. (Insert the jumper connectorswhen the power supply is shared with the receiver.)Gyro outp

•General adjustmentsMake the basic fuselage linkages and adjust-ments according to the helicopter manufac-turer's assembly and adjustment instru

AIRCRAFT ADJUSTMENTS•Revolution Mixing Compensation Ad-justment•IDLE UP 1 ADJUSTMENTWhen high speed level flight is performed with a

•IDLE UP 2 ADJUSTMENT1. When the idle up 2 switch [21] is set to ON, theidle up amount (throttle servo stop position) canbe adjusted with trimme

FP-T8SSHP INVERTED FLIGHT SPECIFICATIONSHANDLING PRECAUTIONS• When the [C] inverted flight FS switch at the rear panel trimmers is switch-ed to the

•FEATURESThe FP-8SSHP is a digital proportional R/C set with PCM (Pulse Code Modulation) for helicopters.The system is extremely noise and dead-point

• The inverted flight function can be turned on and off with the [C] inverted flight FS switch on the trimmer panelatthe back of the set.* INVERT: Inv

INVERTED FLIGHT P REPARATIONS• Set the [C] inverted flight FS switch on the trimmerpanel at the back of the set to the INVERT position.• At this ti

TRANSMITTERCONTROLS22 Hovering throttle ratcheted knob8 CH8 switch33 Rudder button7 CH7 Knob21 Idle up 2 switch20 Idle up 1 ratcheted knob19 Idle

TRANSMITTER CONTROLSBPitchDRudderI ATV/FSbuttonsFig. 3CThrottleE ElevatorsF 2nd ATVH Servo reversingswitchesJ ChannelselectorA Ailerons38 Trimmerpane

SPLINED HORNSThe splined horns allow shifting ofthe servo neutral position at theservo horn.b) EffectSetting and shifting the neutralpositionBase

FP-S130 EXPLODED VIEWSNo.1.2.3.4.5.6.7.8.9.10.11.12.13.14.15.16.17.18.19.20.21.22.23.24.25.Part Name Part No.Upper case FCS 30Middle case FCS 30Bot

FACTORY REPAIR SERVICETo insure prompt service, please follow the instructions given below.1. Charge the batteries for at least 18 hours prior to s

•The receiver is a miniature PCM receiver inwhich the highest reliability has been pursued.It is the first R/C receiver in the world to usethe newest

•TRANSMITTERThis section explains the operation of thetransmitter controls when the servo reversingswitches are in the normal position. When therevers

14.Aileron dual rate switchAileron dual rate ON-OFF switch. When set to thepull position dual rate is turned on, and whenset to the push position,

(19) Idle up 1 switch ( 1 switch)Right ON, Left OFF.(20) Idle up 1 ratcheted knob (1 knob)•When the 1 switch [19] is set to ON, the throttleser

22 Hovering throttle ratcheted knob•Trims the throttle servo independently from thepitch control servo (without regard to mixing).Since the throttl

25 Rotative open gimbal stick• Rotative open gimbal stick allows setting of theoperating direction of the stick within a range of±34 degrees by losen